质量工作通报
Quality Inspection Report
（第54期）
54th version
山东长兴集团公司品管部 2023年11月30日
QC department, Shandong Changxing Group Nov 30th 2023
11月份质量奖惩通报
November Quality Rewards and Punishments Notice
嘉 奖：
reward
部 门 depart | 姓 名 name | 嘉奖内容 content | 奖 励 reward | 备 注 note |
机加工 Mechanical processing | 廖善琼 Liao Shanqiong | 发现外协胶槽侧边加工太薄造成无法正常使用 It was found that the side processing of the outsourcing glue tank was too thin and could not be used normally. | 10元 10 Yuan | |
电焊 welding | 杨立超 Yang Lichao | 外协归正焊合变形，造成整修费用。
| 210元 210 Yuan | 7小时 7 hour |
李强 Li Qiang | 外协小板机水槽焊接垫板高度误差，造成返修费用。 The height error of the water tank welding backing plate of the outsourced small machine machine caused repair costs. | 30元 30 Yuan | 1小时 1 hour | |
横拼部 composer | 高绍瑞 Gao Shaorui | B3L七线托架有方管和槽钢焊接而成，与机架连接用4个螺栓固定，建议改为全部槽钢焊接，固定孔改为2个螺栓固定。 B3L seven-wire bracket is made of square tubes and channel steel welded, and is connected to the frame with 4 bolts. It is recommended that all channel steel be welded, and the fixing holes should be changed to 2 bolts. | 20元 20 Yuan | 不采纳 Not adopted |
高庆洪 Gao Qinghong | B3L大臂滑道效正过于浪费时间，不易调整，建议把大臂滑道支撑架定位孔提前打好便于安装调整，节省时间提高工作效率。B3L boom slide effect is too time-consuming and difficult to adjust. It is recommended to drill the positioning holes of the boom slide support frame in advance to facilitate installation and adjustment, save time and improve work efficiency. | 20元 20 Yuan | 不采纳 Not adopted | |
丁慧超 Ding Hui Chao | 开关固定盒与调节螺母接触部分由于不垂直，并且有焊缝贴不实，建议在固定盒接触部分进行倒角，避免返修浪费安装时间（采纳改固定板并减短10毫米）。 Since the contact part between the switch fixing box and the adjusting nut is not vertical and the weld seam is not firmly attached, it is recommended to chamfer the contact part of the fixing box to avoid repair and waste of installation time (the fixing plate is modified and shortened by 10 mm). | 50元 50 Yuan | 采纳 adopted | |
外协厚薄检开关盒漏焊固定板穿线板焊接方向反，造成拆卸整改。outsourced thickness check switch box was leaking and the fixing plate and wiring plate were welded in the opposite direction, causing disassembly and rectification. | 60元 60 Yuan | 2小时 2 hour | ||
王发启 Wang Faqi | B3拼板机上出料气缸支座处固定孔无丝，需要加螺栓背母，增加平垫和弹垫，建议固定座改为丝孔，直接螺栓安装，节省时间、节约成本。 There are no wires in the fixed holes at the discharging cylinder support of the B3 splicing machine. Bolt back nuts need to be added, as well as flat washers and elastic washers. It is recommended that the fixed seats be changed to wire holes and directly installed with bolts to save time and cost. | 50元 50 Yuan | 采纳 adopted | |
李淑恒 Li Shuhuan | 横拼部用拉杆12*150，建议改成二部10*150，物料统一，节约成本。 The horizontal part uses tie rods of 12*150. It is recommended to change the tie rod to 10*150 for the second part. The materials are unified and the cost is saved. | 20元 20 Yuan | 不采纳 Not adopted | |
小板机用轴φ50，建议改成常规机型φ30或φ40，节约原材料不影响使用。The shaft of the small board machine is φ50. It is recommended to change it to the conventional model φ30 or φ40 to save raw materials without affecting the use. | 20元 20 Yuan | 不采纳 Not adopted | ||
发现外协同步轮攻丝错，避免不良件误用。It was found that the outer synchronized step wheel was tapped incorrectly to avoid misuse of defective parts. | 20元 20 Yuan | |||
外协小板机链轮摆动，无法正常使用，造成拆卸整改。The sprocket of the outsourced small plate machine swung and could not be used normally, resulting in disassembly and rectification. | 60元 60 Yuan | 2小时 2 hour | ||
刘传保 Liu Chuanbao | 横拼机气管在装配连接气管时容易混，市场维修时分辨麻烦，建议改成红绿两种，用不同颜色代替，便于分辨、查找。（采纳改为红蓝两种）The air pipes of the horizontal splicing machine are easily mixed when assembling and connecting the air pipes, and it is difficult to distinguish them during market maintenance. It is recommended to change them to red and green, and replace them with different colors to facilitate identification and search. (Adopted and changed to red and blue) | 50元50 Yuan | 采纳 adopted | |
廖善银 Liao Shanyin | 发现外协B1偏心轮加工面处缺料，无法正常使用。 It was found that the outsourcing B1 eccentric wheel was short of material on the processing surface and could not be used normally | 10元 10 Yuan | ||
竖拼二部 Long core group 2 | 张现亮 Zhang Xianliang | 325大臂支架安装时螺丝孔安装麻烦，需要切割螺栓后安装，建议改为三角形方式用3个螺栓固定，方便安装，提高效率。It is troublesome to install the screw holes when installing the 325 boom bracket. You need to cut the bolts before installation. It is recommended to fix it in a triangular way with three bolts to facilitate installation and improve efficiency. | 50元 50 Yuan | 采纳adopted |
外协归正焊合变形，造成拆卸整修费用。the outsourcing will cause welding deformation, resulting in disassembly and repair costs. | 60元 60 Yuan | 2小时 2 hour | ||
陈建荣 Chen Jianrong | 30元 30 Yuan | 1小时 1 hour | ||
竖拼三部 Long core group 3 | 梁桂辉 Liang Guihui | 外购WPDS减速机漏油，造成装配拆卸整改。The outsourced WPDS reducer leaked oil, causing assembly, disassembly and rectification. | 60元 60 Yuan | 2小时 2 hour |
范文全 Fan Wenquan | 发现外协辊筒内部有异物未清理干净，造成返修整改。It was found that there were foreign objects inside the outsourcing roller that had not been cleaned, causing it to be repaired and rectified. | 20元 20 Yuan | ||
苏德利 Su Deli | 发现4B3电箱高温报警，接线错误，化胶桶线接到胶槽上。It was found that the 4B3 electrical box had a high temperature alarm, the wiring was wrong, and the glue barrel wire was connected to the glue tank. | 20元 20 Yuan | ||
客服部 After Sale service | 李旭 Li Xu | C型拼板机进料上滑道10*90螺杆容易弯，而且位置太小，建议改为B型上进料结构，方便操作避免螺栓弯曲。10*90 screw on the feeding upper slide of the C-type splicing machine is easy to bend, and the position is too small. It is recommended to change to a B-type upper feeding structure to facilitate operation and avoid bolt bending. | 20元 20 Yuan | 不采纳 Not adopted |
邵明岩 Shan Mingyan | 二部拼板机排屑用接近开关安装在排屑下面，很容易卡住垃圾，造成排屑无信号报警，建议更改排屑接近开关位置（采纳改为侧面）。chip discharging proximity switch of the second splicing machine is installed below the chip discharging machine. It is easy for the garbage to get stuck, causing no signal alarm for the chip discharging machine. It is recommended to change the position of the chip discharging proximity switch (to the side). | 50元 50 Yuan | 采纳 adopted | |
加长B1L拼板机水轮后面的同步轮太紧，出现故障时轮子很难拿下来，对维修造成很大的不便，长时间使用后更不容易拿下来，建议把同步轮的间隙加大，方便后期维修。synchronizing wheel behind the water wheel of the extended B1L puzzle machine is too tight. When a fault occurs, it is difficult to remove the wheel, which causes great inconvenience to maintenance. It is even more difficult to remove after long-term use. It is recommended to increase the gap of the synchronizing wheel. Convenient for later maintenance. | 50元 50 Yuan | 采纳 adopted | ||
徐伟升 Xu Weisheng | 归正同步带松弛后需要调紧一些，但是调节的皮带轮挡板由于没有顶丝调节很不方便，建议在挡板处加个顶丝方便调节，提高效率 、节省时间。the synchronous belt needs to be tightened after it is relaxed, but the adjustment of the pulley baffle is very inconvenient because there is no top screw. It is recommended to add a top screw at the baffle to facilitate adjustment, improve efficiency and save time. | 50元 50 Yuan | 采纳 adopted | |
张蕾 Zhang Lei | B3型拼板机使用一段时间加热管出现窜动现象，导致加热接地跳闸，建议加热管固定螺栓背母锁紧，防止加热松动，减少市场问题。heating tube of the B3 type plywood machine has been running for a period of time, causing the heating tube to move, causing the heating tube to trip. It is recommended that the fixing bolts of the heating tube be tightened to prevent loosening of the heating tube and reduce market problems. | 50元 50 Yuan | 采纳 adopted | |
孟凡涛 Meng Fantao | L型齿接机拉料小车底部容易撞断主线，建议打个孔或者用线卡子固定主线，减少不必要的客户损失和售后工作量。bottom of the trolley of the L-shaped tooth splicing machine is easy to break the main line. It is recommended to drill a hole or use a line clamp to fix the main line to reduce unnecessary customer losses and after-sales workload. | 50元 50 Yuan | 采纳 adopted | |
贾兆鹏 Jia Zhaopeng | 工作台铁板太薄，踩上去容易上下反弹有异响，建议中间增加加强筋，增加客户认同感。iron plate of the workbench is too thin, and it will bounce up and down easily and make abnormal noise when stepped on. It is recommended to add reinforcement ribs in the middle to increase customer recognition. | 20元 20 Yuan | 不采纳 Not adopted |
考 核：
Punishment:
部 门 department | 姓名 Name | 考核内容 content | 考 核 Punishment | 备 注 note |
仓储部 Storage | 聂志森 Nie Zhisen | 发江苏福庆鸿木业六尺刀发错，造成市场问题。Jiangsu Fuqinghong Wood Industry issued the wrong six-foot knife, causing market problems. | 50元 50 Yuan | |
电焊 welding | 杨勇 Yang Yong | B1L机架垃圾被动辊轴承座焊接误差，造成返修整改。welding error of the passive roller bearing seat of the B1L frame garbage caused the repair and rectification. | 50元 50 Yuan | |
电工组 electric | 苑朋刚 Yuan penggang | 齿接机CX2309-GT-7配辅助光电型号配错。 ear splicer CX2309-GT-7 is equipped with the wrong auxiliary photoelectric model. | 50元 50 Yuan | |
打磨喷漆 Polishing&painting | 杨凤强 Yang Feng Qiang | 拼板机CX03LB1-5外观检查不仔细，机架底座油漆脱落，外观起皱。appearance of the CX03LB1-5 puzzle machine was not carefully inspected. The paint on the base of the frame fell off and the appearance was wrinkled. | 50元 50 Yuan | |
机加工 mechanical | 孙秀岭 Sun Xiuling | 前进料气缸固定座2*φ25孔漏打，造成返工整改。2*φ25 holes of the front feeding cylinder holder were missed, causing rework and rectification. | 50元 50 Yuan |
编 制： 品管部 审 核： 批 准：
Compiled by: QC depart Reviewed by: Approved by:
山东长兴（集团）有限公司将继续以科技进步为基石，加快企业的转型升级。以“赋能用户，让未来发展不可思议”的使命，领先的国内、国际市场份额，打造具有国际竞争力的木业机械制造企业，成为中国木业机械领军企业。
Shandong Changxing (Group) Co., Ltd. will continue to accelerate the transformation and upgrading of the enterprise based on scientific and technological progress. With the mission of "Empowering users for incredible future growth", we will build an internationally competitive wood machinery manufacturing enterprise with leading domestic and international market shares and become the leading wood machinery enterprise in China.
扫描二维码关注长兴板机
山东省临沂市费县探沂工业园振兴路8号
